27/05/2015
shen wei
- add in disble ejector motor and enable button if ejector movement fail

26/05/2015
shen wei
- remove XY cut line and XY home to Tape Center PEB value boundary check

19/05/2015
shen wei
- add in FW workaround to fix the issue that media present sensor is not able to detect B509 which is black backing media.

18/05/2015
Ramesh
- Capping the xy cut offset value to the boundary limits when they are outside of boundary limit.

27/04/2015
Ramesh
- Manufacturing Diagnostics(prn) and Main Editor(lbl) Print and XYCut calibration file updated by generating both these files from the same Markware source file.
  This is to avoid the difference seen in the output.

13/04/2015
Ramesh
- Defect fix #71931 - SQA - Exponential position shift in XY cut for longer length label.

13/04/2015
Eng
- Bug fix - 71942: Default Korean IME font shall be in malgun

11/04/2015
shenwei
- Bug fix - 71939: Inconsistent print registration for E-Prep with button holes

02/04/2015
Ramesh
- Updated xycutter.ini with CrossRange sections for better start and end meeting.

01/04/2015
Ramesh 
- Modified XY Cutter thread priorities to address the defect #71834 - SQA - Intermittently the cut circle deformed in 36 inch print and xy cut test label.

1/4/2015
Eng
Bug Fix 71792: SQA - The bottom cut of weeding is missing when cutting two text objects(attached test file).

1/4/2015
shenwei:
Bug fix 71882 - GHS 4" pre-printed label diamonds not formatted properly

30/03/2015
Ramesh
- Defect fix #71834 - SQA - Intermittently the cut circle deformed in 36 inch print and xy cut test label.

27/03/2015
Ramesh
- Disabled DupPointTol optimization parameter in xycutter.ini file.

26/03/2015
Ramesh
- Reduced the end cut travel distance during fixed label size xy cutting to make the output label size as the defined size.

26/03/2015
Eng
Bug Fix 71817: SQA - The Korean fonts are inconsistent with Primo.

24/03/2015
Ismail
Bug Fix 70554: SQA - If we open the printer cover just after installing a diecut media throws "Printer cover opened during printing (Error Number:16)" Error message. 

20/03/2015
Ismail
Bug Fix 71867: SQA - Printer is throwing "Printhead not aligned error message (Error number 89)" when we replace the ribbon during ribbon out error messge and the printer is going to freeze state

20/03/2015
shen wei
Bug fix 71873: SQA -The printer is giving "Media Jammed Error Message (Error number 54)"  when we replace the media from continuous to diecut after giving a printjob using continuous media
        71874: SQA -The printer is giving "Media not loaded correctly (Error number 54)"  when we replace the media from continuous to GHS Diecut material after giving a printjob using

19/03/2015
Ismail
Bug Fix 71864: SQA - Printer UI freezes when we cancel a printjob during media registration 

18/03/2015
Shen wei
limit the print&XY cut margin printable area to 3.8"

17/03/2015
Eng
- Bug Fix 71826: SQA - The actual label is slightly shorter than defined length for XY cut label set to cut at end of job
- Bug Fix 71851: SQA - The actually supported max label length for xy-cut is 37.24 in instead of 36 in.

17/03/2015
shenwei:
implement the fast reverse speed (3IPS) during tape alignment for continous non clockspring media 

12/03/2015
shenwei:
Bug fix 71836 - SQA - Korean and Japanese fw should not include graphics with Simplified-Chinese characters.
Bug fix 71837 - SQA - XY cut printing is not proper if user provides the latest PEB values

11/03/2015
Ismail
Bug Fix 71780: SQA - if press cancel button in error 58 triggered by USB peripheral job, then open the cover, printer shows cover open during printing error16"

10/03/2015
shen wei:
bug fix 71794 - SQA - Feed,Cut and Power buttons  are not working further ,once we press feed or cut button
ribbon flow change to resolve veritcal wrinkle

09/03/2015
Ismail
Bug Fix 71775: SQA - Pannel ribbon out error is not properly handled, printer keep doing color searching without ribbon installed

05/03/2015
Ramesh
- Handling of XY Cutter Moveto command in firmware.
- Enabled XY Cutter tape jam detection.

05/03/2015
Eng
- Bug Fix 70652: SQA - XY cut only job is notable to be print correctly in fixed length, when the xy cut object is in the leading edge side

04/03/2015
Ismail
- Bug Fix 71772: SQA - Printer report ribbon outif press and hold feed button for a long time

03/03/2015
shen wei:
bug fix 71774: SQA - Intermittent error 54 fr spot color printing

03/03/2015
Ramesh
- Improved overall xy cut job speed by ~7 seconds. 
Areas improved,
1. Print line to xy cut line movement speed increased to 2.5 ips from 1 ips.
2. Carriage homing is done after end cutting.
3. Carriage homing speed increased to 2.5 ips from 1 ips.

26/02/2015
Eng
- Bug Fix 71619: SQA - Not able to cut chinese character in SC package
- Bug Fix 71625: SQA - No cuttable characters are availabe if inputing letters or numbers when the font is SimSun.

25/02/2015
Geetha
- Bug Fix: 71102
- Bug Fix: 71103
- Bug Fix: 71403

24/02/2015
Ramesh
- Defect fix #71730 - SQA - xy cut object shift in cross web direction with 36 inch label, circle object being print and xy cut.
- Disabled down web position logging.
- XYCutter.ini file updated to have the starting point along the horizontal(tape) direction.

23/02/2015
Dheeraj
- Bug Fix 71557: SQA - User diagnostics window is not displaying more than 20 error logs
- Bug Fix 71736: SQa -None of the error information is being displayed in user diagnostics when we boot through NAND

23/02/2015
shenwei
- Bug fix : 70981 - SQA - No Demo labels in badger

17/02/2015
Kishor
- Bug Fix:71679:SQA - Issues for "Text Print/Cut" help in both English and Simplifed-Chinese.

17/02/2015
Geetha
- Bug Fix: 71516, 69084, 71634, 71401

16/02/2015
Kishor
- Bug Fix: 71683:SQA - Punctuation issues in Circle Guage's help message screens.

14/02/2015
Eng
- Bug Fix 71464: SQA - When BWS send down a mono label with XY object, 2 copies, cut at end of job, printer keep reversing tape after xy cut

13/02/2015
Kishor
- Bug Fix: 71678: SQA - The Simplified-Chinese translation of "Create New File" is wrong in Gradeint Scale Label.

12/02/2015
Ismail
- Bug Fix 71659: SQA - Feed and cut is not happening when we interrupt a printjob with printer cover open with diecut media installed


12/02/2015
Ramesh
- Temporarily reverting the changes for the XY Cutter pause issue. Now, allowing the job to get completed rather than cancelling.
- Firmware support for XY Cut offset setting feature from eSW.

10/02/2015
Ismail
- Bug Fix 71445: SQA - error message is not proper when swap between panel ribbon and mono ribbon

09/02/2015
Ismail
- Bug Fix 70953: SQA - Label Update is not happening when printer resumes from sleep mode if we replace the media type when the printer is in sleep mode

06/02/2015
Ramesh
- Improvements in XY Cutter codes with all movement related errors handled.
- Defect fix #71624 - SQA - The printer pauses for some time then continues during X-Y cut print job.

06/02/2015
Ismail
- Bug Fix 71433: SQA - Printer will be in Hangstage for around 2min when user tries to cancel XY printjob during PH lift movement

03/02/2015
Ismail
- Bug Fix 71556: SQA - Feed or cut operation is not working if we press the cancel button when printing in progress from User diagnostics menu

03/02/2015
Geetha
- Bug Fix: 71565, 71598, 70977, 71567, 71611, 71638, 71531

02/02/2015
Sai
- Bug Fix: 71580,71605,71606

30/01/2015
Ismail
- Bug Fix 71461: SQA - Tape out detection is not happening while printing Cut only objects

29/01/2015
Ismail
- Bug Fix 71554: SQA - During Data rasterzation if we open the print door Ribbon will be fused with the roller & motor keeps rotating,& printer goes to freeze state
Eng
- Bug Fix 71615: EM3.0 Compliance Test - Print XY Cut extra labels
- Bug Fix 71559: SQA - Quick label template application is not available in EU package
- Bug Fix 71619: SQA - Not able to cut chinese character in SC package

29/01/2015
Ramesh
- Defect fix. #71620 - SQA - BBP35 prompt error 92 xy cutter jam after power up.
Eng
- Bug Fix 71619: SQA - Not able to cut chinese character in SC package
- Bug Fix 71559: SQA - Quick label template application is not available in EU package

28/01/2015
Ramesh
- Crossweb shift improvements. This also improves print and xy cut alignment.

27/01/2015
Ismail
- Bug Fix 71560: SQA - During Initialisation other than media & ribbon errors are not being displayed.
Eng
- Bug Fix 71422: SQA - Unable to apply "cut text" property to chinese characters

23/01/2015
Kishor
-Bug  fix #71540: Updated CLP pipemarker name and HSID Pipemarker name to solve the issue  of truncation in croation language.
-Bug  Fix #71565: The translation of "Show Black Outline" in Gradient Scale Label is corrected in Simplified Chinese.
-Bug fix  #71517: Updated ZS_PlEditor to prevent the truncation of the string in print status dialog.

22/01/2015
Ismail
- Datastarvation code check in
Eng
- Bug Fix 71484: SQA - With EU package, the tape is not reversing and then feeding forward and no cutmarks are printed in between each copy when cut option is "At the end of job".

21/01/2015
Ismail
- Bug Fix 71434: SQA - XY Cut - On SensorHeadLiftHomeFailed error (EID:89) when user tries to Click on Resume next option printer goes to freeze state

20/01/2015
Eng
- Bug Fix 70553: SQA - when supply saver is turn on, the margin is omitted.

19/01/2015
Ismail
- Bug Fix 71428: SQA - If we resume a printjob with a corrupted meida installed (improper-encryption-no:48 ) or without media installed(no:49) "Error number 52 (Media remaining value has reached zero)" error message is thrown

19/01/2015
Sai
- Bug Fix: 71527,71532,71541

19/01/2015
shen wei
- fix bug : 71467 - SQA - Extra line is printed for eprep 1x0.5 inch diecut

19/01/2015
Ramesh
- Modified XY Cutter Pinch drive logic with capability of handling intervention errors scenarios.

16/01/2015
Geetha
- Bug Fix: 71456, 71468,71515,71451,70694,70976,71503,
+ Bavkground color retaining in ruler
Eng
- Bug Fix 71469: DVT EM3.0 System Life Test - Main Editor unable reflash image when opening print file
- Bug Fix 71305: DVT EM3.0 System Life Test - Incomplete printout on pg 19

14/01/2015
Unni
- Bug Fix: 71333: ribbon and media values get default when ribbon and media remaining values are zero
- Bug fix 71463: error log does not display all kind of errors 
Eng
- Bug Fix 71311: SQA - In GHS/CLP the diamond of the graphics is overlapping with the preprinted red diamond on the diecut meida.

14/01/2015
Ramesh
- Modified CrossWeb and DownWeb motor Stop function to support controlling of motor driver disable functionality as and when needed.
- During XY cut operation, motor gets disabled only during direction change alone.
- Added XYAxisMovement object to CPrinter class.
- Facility to dump the xy cutter system ramp profile data from RampGenerator module.
- Minor code clean-ups.

13/01/2015
Dheeraj
- Bug Fix 71521: SQA - The default value of label szie in ruler/circle guage is still 3.96in when no tape is installed.

08/01/2015
Ramesh
- Defect fix #71419 - SQA - During XY Cut Printer hangs & contiously feeds the media when user try to open the print cover during printing process.

Ismail
- Bug Fix 71425: SQA - Media Wiper arm error messages (error no:21 and 22) are disappearing for alternate printer cover open/close sequences

07/01/2015
07/01/2015
Ramesh
- Defect fix #71160 - SQA - Progress bar shall appear during encoder engagement

Geetha
- Bug Fix: 69674, 71396

06/01/2015
Ismail
- Bug Fix 71404: SQA - Improper printing of the color object is observed in EM3.0 printer when Multi color ribbon is installed

02/01/2015
Geetha
- Bug Fix: 71473

31/12/2014
Geetha
- Bug Fix: 71441, 71458

30/12/2014
Ramesh
- Attempted a fix for the position issue.
- Increased pinch/unpinch timeout to 10 seconds from 5 seconds.

30/12/2014
Geetha
- Bug Fix: 71457, 71751, 71752, 71454, 71549, 71460

26/12/2014
Ramesh
- Changed vref to 215 as per ME inputs for all xy cut related movements.
- Reduced object to object movement speed to 2 ips from 2.5 ips.
- Increased xy cutter ramp size to 300 mil distance from 200 mil distance.
- Some code clean-ups.

24/12/2014
Geetha
- Bug Fix: 71437,71444

23/12/2014
Ismail
- Bug Fix 71424: SQA - If we open and close the printer cover when there is a Color needed error message (Error no:63) with a single color label created,the printer starts printing with the installed ribbon color

23/12/2014
Ismail
- Bug fix 71427: SQA - tape slightly overshoot when end of tape is detected

23/12/2014
Geetha
- Bug Fix : 71416, 71416 

22/12/2014
Shen Wei
- Bug fix 71354 - SQA - Intermittently printer is not able to find leading edge properly for diecut media when cutter is cut at each label
- Bug fix 71069 - SQA - 2 Tags are being printed for a single copy of print job

22/12/2014
Geetha
- Bug fix : 71412, 71346, 71104

22/12/2014
Ismail
- Bug Fix 71417: SQA - On canceling printjob during Print head alignment, printer throws error 89 message continously

19/12/2014
Geetha 
- Bug Fix 71352, 71345,71395

19/12/2014
Ismail
- Gated auto launch : Added FW workaround for auto launch and printing after auto launch

17/17/2014
Ramesh
- Modified voice coil drive control logic as per EE direction.
- Fixed a movement related issue that involves only one axis movements. This also fixes the motor stall issue seen by DVT team.

17/12/2014
Ronald
- Fix bug 71393: SQA - If print job from Brady workstation is mono and cut at end of job, printer is not end  cut properly and report error 54 after end cut
- Fix bug 71336: SQA - ribbon mech keep moving after door open during feed button is press and hold

15/12/2014
shen wei
-bug fix 71337 - CurrColorIndex is not updated after printer cover is closed.

12/12/2014
Ramesh
- Enabled XY Cutter error handling(Initial version).
- Cleared dead codes.

12/12/2014
Geetha
- Handle the resize scaling for non stretchable objects (Eg: Circle etc)
- XY Cut error Handling

11/12/2014
Ismail
- Bug Fix 71309: OPEN SP30: Print position for second copy (cut at EOJ) of die-cut gap media is dependent on Ramp profile

11/12/2014
shen wei:
-bug fix 71069: SQA - 2 Tags are being printed for a single copy of print job

11/12/2014
Ismail
- Bug fix 71327: SQA - Print fail and error 45 is shown if user send print job during initialization

10/12/2014
Ismail
- Bug Fix 71315: Fail to auto launch from SD due to cs125432

10/12/2014
Geetha
- Support Sign Header Graphics for:Turkish,Estonian and Croatian

10/12/2014
Shen wei
- Bug fix - 70689 & 70658

09/12/2014
Ramesh
- Modified XY Cutter position management from rasters to step and encoder counts to aid position accuracy improvements.

09/12/2014
Geetha
- Bug Fix: 71068: (Platform) SQA - On click of change template button,application throws an "Invalid supply message "instead 
of taking user to selected template window Close Editor  
- Updated GHS translations
- Include Remotelink exe in release packages

08/12/2014
shen wei
- Bug fix: 71109 - SQA - Can not generate SwitchWiperNeedsEngage(E21) and SwitchWiperNeedsDisengage(E22) on Badger.

08/12/2014
Geetha 
- Bug Fix: 70342

05/12/2014
Ismail
- Resolved sleep/suspend issue seen on EM3.0 (Known Issue: It fails intermittently after print head movement)

04/12/2014
Geetha 
- Bug Fix: 71298 and 71295
- Added Circle and Ruler gauge app in APAC and Europe packages

04/12/2014
Ramesh:
- Baseline the xycutter.ini file parameters based on latest changes in eSW.
- During xy cutting, object to object movement speed changed from fixed to ramping speed, maxing upto 2.5 ips. This will help throughput.
Above changes are only in EM3.0 branch.

04/12/2014
Geetha
- Bug Fix: 71296

02/12/2014
Geetha 
- Bug Fix: 70781

01/12/2014
Geetha
- Bug Fix: 71040, 70980, 70873

28/11/2014
Shiva
Bug Fix 71170 : SQA - Finish&Cancel buttons on circle/ruler guage label setup screen take no effect after changing supply and dismissing Invalid Supply msg.
Bug Fix 71175 : SQA - Unable to come back to the label from the edit dialog if any other error pops up while editing/creating a Circle gauge/Gradient scale label

29/11/2014
Sai
- Bug Fix #71074 : eSW - update string translations of circle and ruler gauge apps after review comments 

28/11/2014
Shiva
Bug Fix :SQA - The shown label size on the status bar is always 1.00x2.00 when creating ruler guage label using blank diecut media(e.g. 4x6, 1.15x2.85).

28/11/2014
Geetha
- GHS Tranlation update for ET HR SK
- Bug Fix 71265, 70955

28/11/2014
Ramesh
- Corrected max xy cutter speed to 2.5 ips that was limited to 2 ips. 
- Updated xycutter.ini file.
Above is done only in EM3.0 branch.

27/11/2014
Shiva

Bug Fix- 70937 :SQA - Improper label creation in gradient scale application with diecut media installed
Bug Fix- 71157 ::SQA - Cut circles are shown in the preview box and in the label editor and are actully cut in the prined label when using uncutable small media to create circle guage label with fw 50.171.

27/11/2014
Geetha
- Updated all the checkbox state ON status in all Print/Cut panels
- Cut Settings Update as per installed ribbon
- Supply saver flow changes
- Print Boundary Support
- Bug Fixe: 70312,70817, 71098 ,71165, 70345, 70812,69813, 70618, 71051
- Updated the pipemarker preferences for supplysaver and printboundary
- Updated GHS translation and configurations

26/11/2014
shen wei:
- Bug fix #71156: SQA - When Installed Media is None XY cutter blade message showns requires "blade height 1" instead of "None"

24/11/2014
Ismail:
- Bug Fix #71046: Known Issue: After Tape out detection, open door and change the die-cut media then ribbon continuously moves during threshold computation until reboot

20/11/2014
Ramesh:
- Defect fix #71158 - DVT Pre EM3.0 System Test Verification - During Snap Elllipse XY cutting, the platen motor stallled when media movement is in downweb direction and not able to cut ellipse shape properly.
- Cleared of some dead codes.
- Minor code cleanups.

19/11/2014
Eng:
- Bug fix 71180 - DVT Pre EM3.0: Not able to xy cut using the Snap Q file when print width is set to 3.8" (in smartcell).  It seems that the text 'ag' and 'BX' are causing the issue. There is no problem when print width is set to 3.96" in the smartcell.

19/11/2014
Shen Wei:
- Bug fix 71109 - SQA - Can not generate SwitchWiperNeedsEngage(E21) and SwitchWiperNeedsDisengage(E22) on Badger.

18/11/2014
Eng:
- Special applications able to launch from main editor.

18/11/2014
Ismail:
- Bug Fix 71162: SQA - Improper feed and cut after print (cutting on the printed label) with slower print speeds (<=3 ips) intermittently
- Bug Fix 71173: SQA - Printer is feeding out the media with the set print speed value for feed button press

18/11/2014
Geetha:
- Bug #70796: SQA - Press OK to continue with the '-' color information in the color needed error message is improper 
- Bug #71056: Open Issue - eSW - Handle mismatch flow on opening a temp label

17/11/2014
Geetha:
- Bug Fix 71097: SQA - Pipe diameter maximum value entry exceeds the limit (>27 inches) in "Rollform" and "symbol or arrow tape" styles of CLP pipemarker
- Bug Fix 69737: Text is overlapped with color bar on Color Needed(E63) screen.

14/11/2014
Ismail:
- Bug Fix 70849: SQA - Power button press to wake up the system from sleep is not working consistently

07/13/2014
Shiva:
Bug Fix 71000: SQA - The portrait ruler guage label is partically shown in the editor and there is no Down arrow button whe side A value is larger than the printable width.


07/11/2014
Shiva:
Bug fix : 70968 : SQA - Screen is not reflashed correctly during screen transition in Circe guage app.
Bug fix : 70571 : SQA - Circle Gauge UI is getting hanged when we access the color picker,outline and edit dialogs multiple times
 

11/11/2014
Ramesh
- Defect fix #71135 - SQA - intermittently xy cutter not engaged before moving the carriage.

11/11/2014
Ismail:
- Print speed adjust implementation

07/11/2014
Shiva:
Bug Fix: 71000 SQA - The portrait ruler guage label is partically shown in the editor and there is no Down arrow button whe side A value is larger than the printable width.
Bug Fix : 70988: SQA - The default green color in the circle/ruler guage is obviously different from the green color selected from color picker.

07/11/2014
Ismail:
- Updated code for side notch die-cut and common code for all die-cut media

07/11/2014
Ramesh
- Fixed XY Cutting issue when running from NAND. Fixed only in EM3.0 branch.

06/11/2014
Ramesh
- XY Cutter enabled to support cutting upto 2.5 ips. Only EM3.0 branch code supports this.

06/11/2014
Geetha
- Updated versions to firmware = 011 and software = 001.100.008

06/11/2014
Ismail:
- Implemented robust algorithm for analog sensor transitions

05/11/2014
Shen Wei:
- fix bug 70974: SQA - Improper TAB order in ArcFlash Templates (4x6)

04/11/2014
Ismail:
- Diecut code changes to address wrong ADC value during ADC read

03/11/2014
Shiva
Added Menu Diasabled Button for Ruler and Circle Apps


03/11/2014
Ismail:
- Diecut code changes to compute threshold to threshold saved value from upstream analog sensors to address position drift

03/11/2014
Shiva
Bug fixes 70645 SQA - The shown Label Size on the status bar is not refreshed immediately after changing tape when Circle Guage app is launched. 
Bug fixes 70976 SQA - The circle guage label size in the editor is inconsistent with the shown label size on the status bar and the kept label size in editting label setup flow after the supply change.
Bug fixes 70988 SQA - The default green color in the circle/ruler guage is obviously different from the green color selected from color picker.

03/11/2014
Geetha
- Bug Fix 71023: SQA - Error message for multiple mismatches is diaplyed for a single supply mismatch 
- Bug Fix 69816: The error msg of E45 is inconsistent with Badger Error Messages_v4.6.
- Bug Fix 69861 ( Modified): The msg of E53 is inconsistent with Badger Error Messages_v4.6\
- Bug #70352 Fix : (Platform)Open Item: Extra empty space added in config label print
- Task #69515 ( Modified): eSW - Remove the User Diagnostic dlls from the datafiles

30/10/2014
shen wei:
- Bug fix: 71007 - SQA - For Tag media cutter blade message shown is "Installed media is none" insted of "Installed media not Xy cuttable"

shen wei:
- Bug fix: 70813 - SQA - RTK 4 x 6 NFPA standardard label is not properly displayed in main editor

28/10/2014
Ismail:
- Threshold computation for both upstream and downstream analog sensors (Gap and Center Notch)

24/10/2014
Ismail:
- Bug fix 70842: SQA - On interrupting the print job & retry the print operation observe unable to perfrom the print operation

23/10/2014
Ismail:
- Bug fix 70699: SQA - Improper cut during tapeout detection on diecut medias

21/10/2014
Ismail:
- Updated cut button flow

20/10/2014
Ismail:
- Tape alignment flow changes implementation

17/10/2014
ShenWei:
- FW to provide information to embedded software on knife position based on smart cell data

14/10/2014
Ismail:
- Bug Fix #70659: SQA - Printer doing tape alignment and give wrong error with no tape or ribbon installed

09/10/2014
Shen Wei:
- Fix RTK template bugs: #70838, #70828, #70809, #70810, #70814

08/10/2014
Ismail:
- Issue fix - Printer hangs before printing second color.

07/10/2014
Ronald:
- Bug fix 70800: SQA - Side notch diecut print speed is not right in build 118 (This was solved before but has some issue if the printing uses stepper so the code changes specifically for printing using stepper issue)
- Bug fix 70830: SQA - When using mono swap to print RTK diamond only label, there is 2-5 seconds redandent ribbon movement after end cut 
					   (This is caused by not checking the number of panel on the ribbon so the extra ribbon movement should only applicable for panel ribbon)

07/10/2014
Ismail:
- Data starvation code check in

06/10/2014
Shiva
- Bug fix 70646:Open-Item:  the printer should pop up Label Too Wide error to block circle guage label printing when label size is biggger than tape width.
- Bug fix 70185 The shown printable area in the editor of small size tape is changed to the same as 4in tape after clicking Cancel on circle guage/gradient scale Label setup .

02/10/2014
Ronald:
- Bug fix 70800: SQA - Side notch diecut print speed is not right in build 118

01/10/2014
Ismail:
- Updated tape smart cell structure as per smartcell specs v1.1
02/10/2014
ShenWei
- check in PEB calibration first pass using magic media for sensors.

01/10/2014
Dheeraj:
- Bug 70693: SQA - Error message 52 is not being displayed eventhough the tape remianing value is 0

01/10/2014
Dheeraj:
- Tape cell dialog updated as per smartcell specs v1.1

30/09/2014
Ismail:
- Feed and cut flow implementation as per Badger 3-Button flow on confluence

26/09/2014
Ismail:
- Bug fix 70691 : DVT Em2.0 System Life Test - Image drift on die cut media B595 4" width

26/09/2014
Ramesh:
- Updating xycutter.ini file based on ME testing.

25/09/2014
Ronald:
- Fix bug #70776: SQA - Error 89 is seen very often during print job initialization

23/09/2014
Ronald:
- Fix Bug #70320: DVT EM2.0: System Life Test - Ribbon Multicolor Skip Panel
- Fix Bug #70346: SQA - Intermittent ribbon slippage during color searching, caused error 84
- Fix Bug #70535: SQA- Panels skipping if we do printer cover open & close  between two multicolor print  jobs of full panel length
- Fix Bug #70766: SQA - Intermittently printer print on wrong color panel during KRGB spot color printing

23/09/2014
Geetha 
- Bug #70704: SQA - Keyboard is not accessible after doing a printjob cancellation

22/09/2014
Ramesh:
- Fix for the ribbon feed out and cut quality issue seen with the changes made on 18/09/2014. 

22/09/2014
Ronald:
- Enable eCAP for raster timing.
- Disable interrupt from stepper motor during slew speed.
- Change ribbon rocker arm delay from using timing to steps.

19/09/2014
Ronald:
- Update on firing algorithm for 2ips printing to solve downweb white lines issue.
- Fix for white lines at the start of the print. (Continuous media only)

18/09/2014
Ramesh:
- Enabled error handling infrastructure.
- Modified the flow slightly to suit error handling.

17/09/2014
Geetha:
- Updated the XYcutter depth and accuracy
- Updated the ISO graphics with udpates from UX team (15/09/2014)

12/09/2014
Ramesh:
- Defect fix #70654 - SQA - Cut Depth setting for a printjob is not retaining between ribbon swap.

09/09/2014
shen wei:
- fix bug 70375 - DVT EM2.0 System Life Test - Wrong cut position on B551 side notch tag stock media

08/09/2014
Ramesh:
- Applying XY Cutter PEB calibration parameters.

08/09/2014
Geetha
- New European graphic support in NA, EU and APAC region packages

08/09/2014
Ronald:
- New ribbon subsystem control implementation.

04/09/2014
Eng:
- Fixed for peripheral XY Cut (when Cut Setting is End label)

05/09/2014
Ramesh:
- Fixed an issue related to tape alignment failure during xy cut only job.
- Enabling IOControl flow logging. This has no functional impact and meant only for developer debugging. By default, logging is disabled.

04/09/2014
Eng:
- Bug Fix 70520/70555 :  DVT EM2.0 System Life Test - Extra down web  line on extreme left of label is seen

1/09/2014
shen wei:
- look for smartcell usestepper mode bit to decided whether to print using stepper mode.
- turn on center notch die-cut printing.

29/08/2014
Eng:
- Color ini is updated based on Badger_color_ini_140828.xlsx

27/08/2014
Shreekeerthi:
Bug Fix 70532: Printer hangs for multicolor printjob cancellation from standalone.

27/08/2014
Ismail:
Task #70477: FW - Tape and Ribbon smartcell structure update as per FIT memory cell specs (Rev 0.9)

27/08/2014
Ramesh:
- Defect fix: #70529 - SQA - Extra blank label is getting added up in the trailor while printing of text object with a cut only object or print&cut object in multicolor with paneled ribbon installed.
- Defect fix: #70316 - SQA - The trailer edge is too big when a XY CUT only job is executed.

26/08/2014
Shreekeerthi:
Bug Fix 70554: If we open the printer cover  just after installing a diecut media throws "Printer cover opened during printing (Error Number:16)" Error message. 

26/08/2014
Ramesh:
Defect Fix: #70537 - Printer hang when cancel a XY cut standalone job.

22/08/2014
Shreekeerthi:
Bug Fix 70337: Media Smartcell remaining value is not getting updated after successful print of an xy cut label.

21/08/2014
Geetha:
Bug Fix 69746: The label in the main editor is not automatically updated in some scenarios.

21/08/2014
Ronald:
Bug fix 70455, 70465: Multi color print alignment issue and shorter end cut length.

20/08/2014
shen wei 
Bug fix: #70394 - DVT EM2.0 System Life Test - Printer hang during printing

19/08/2014
Ramesh:
- Added capability to get the current cut force setting from firmware. 
- Made changes to use nominal cut force value during power-up and door open/close. This value will be used as default till software over rides.

19/08/2014
Shreekeerthi:
Bug fix 70257: The pinter behaviors are incorrect when PH Too Cold(E22) occurs.

19/08/2014
ShenWei:
Bug fix: # 70053 - DVT EM2.0- Intermittenly ribbon slip during initialization of a peripheral diecut print job
add timeout of 10s for ribbon movement

18/08/2014
Geetha:
Bug Fix #69790: On Line Status diaglog and Error Reading Ribbon Smart Cell error still stick on the main editor screen if 
openning/closing the cover after error pops up in the peripheral printing.
(Error Handling from peripheral if the first color is other than Error 63)

18/08/2014
Shreekeerthi:
Bug fix 69862: MemoryMediaRibbonMismatch(E69) should not block printing.

18/08/2014
Shiva:
Bug Fix 70150 : The logic of vadilty check for Start/End Value fields in In-Range Zone is incorrect.
Bug Fix 70159 : Error still pops up when the option(Before In-Range Zone, After In-Range Zone, Show Range Indicator) is unchecked.
Bug Fix 70133 : The validity check for Start/End value of My Guage Range is incorrect for some values.
Bug Fix 70118 : The shown label size on the status bar is changed to 4.24xAuto after clicking Cancel to give up Circle Guage label creation.
Bug Fix 70118 : A circle guage label is created unexpected when clicking Label Size area on the status bar and then clicking Cancel.

14/08/2014
Shreekeerthi:
Bug fix: Tape smart cell value reduces twices only for 2 color print.

14/08/2014
Geetha:
- Bug #70323: Weeding box of xycutter text is not rotate

14/08/2014
Ronald:
- Bug Fix #69721 - The object printed after the full square graphic is always in the wrong position if pressing ok on E63 to continue printing with mono ribbon.

14/08/2014
Shen Wei:
- Bug fix: #70385 - DVT EM2.0 System Life Test - Printer smart cell reflected 0 on B584 and B595 (in between print jobs)
- Bug fix: #70050 - SQA - Intermittently media continue feedout when printing diecut media B33-18, Y140711 diecut media from Brady Workstation at 4 ips
- ADC one shot readng code change in BSP

13/08/2014
Ismail:
- Fix for die-cut gap half cut media and false peak detection for die-cut gap (Bug #70363)

13/08/2014
Ronald:
- Fix color ribbon skipping issue during multicolor printing.

13/08/2014
Ramesh:
- Minor enhancement to Print and XY Cut flow. As per ME request, tensioned the ribbon after 1 inch before reversing the tape.
- Fixed an issue on Print and XY Cut where during the first print and xy cut job after power cycle, cross web position will be offset.
- Defect fix #70317 - SQA- Feed to cut distance is not enough when printing labels with XY cut and printing object.

12/08/2014
Shreekeerthi:
- Tweaking of formula for symmetric and unsymmetric side notch media
- Bug Fix 69943: Printer not able to print diecut B30-242-7569

12/08/2014
Geetha:
- Bug Fix #70031: Assign the current color picked to date/time object

07/08/2014
Ismail:
- Cut button flow as per Plasma 3 button flow (https://bradycorp.atlassian.net/wiki/display/BP/Plasma+3-Button+Flow)

07/08/2014
Ronald:
- Bug Fix: Bug#69802, #69673: Process color printing not able to print the 2nd panel and panel start printing at the clear gap.
		
06/08/2014
Geetha: 
-Multiple Copy die-cut label print support
-Bug Fix: Bug #69603: The label frame is printed unexpected when only cut label frame option is checked. ( Support label print with combination of cur and print objects)

Eng:
- Bug Fix: Bug #70307: In print and cut a label with text (print only, rotate) and rectangle (xycut only), printer infinite waiting for xy cut data during xy cut phase.

04/08/14	
Ronald: 
- Implement additional flow for color searching by keeping the history of the previous printed color. This is to solve ribbon skipping issue.

31/07/14	
Ronald: 
- Integrate additional tape rewind flow and tape rewind new speed
- Added 1 inch movement forward of media during 2nd and subsequent color searching process to peel the media from ribbon

23/07/14
shen wei: 
-Enable center notch calibration
